Skip to content
Safety Guide

Working at Heights: Essential Safety Rules for Construction Workers

By WhiteCard Prep Team · Last updated: 9 min read

Safe Work Australia describes working at heights as a high risk activity and a leading cause of death and serious injury in Australia. Its latest national statistics show that falls from a height were the second most common cause of worker deaths in 2025 (28 deaths, 13% of all worker fatalities), a position they have held for three years in a row, and that the construction industry recorded 41 worker fatalities in 2025. SafeWork SA also notes that about half of fatal falls involve heights of three metres or less. Understanding the rules, the equipment, and the mindset required for working at heights is critical for every person who steps onto a construction site.

Practice heights safety questions

Our Working at Heights topic has dedicated practice questions covering falls, scaffolding, and harness systems.

The 2-Metre Rule

Under the model WHS Regulations (regulation 291), construction work that involves a risk of a person falling more than 2 metres is classified as high risk construction work. Victoria uses the same 2 metre trigger under its OHS Regulations 2017. This classification triggers specific legal requirements:

  • A Safe Work Method Statement (SWMS) must be prepared before work begins
  • The PCBU must ensure all reasonably practicable control measures are in place
  • Workers must be given the information, training and instruction they need to do the task safely
  • On a construction project, a copy of the SWMS must be given to the principal contractor before the work starts

Importantly, the 2-metre threshold does not mean falls below 2 metres are safe. The general falls rules in the WHS Regulations (regulations 78 and 79) apply to any fall from one level to another that is reasonably likely to cause injury, whatever the height. The 2-metre rule defines when a SWMS is needed, but risk assessments should consider all fall hazards regardless of height.

State note: South Australia previously set the high risk construction work fall height at 3 metres. SafeWork SA has announced the reduction to 2 metres, with a transition date of 1 July 2026.

Fall Prevention vs Fall Arrest

There is a critical distinction between preventing a fall and arresting a fall that has already started:

  • Fall prevention devices (passive): Physical barriers and platforms that stop a person from falling in the first place, such as guardrails, edge protection, scaffolding and elevating work platforms. These are preferred because they require no action from the worker
  • Work positioning systems: Systems that hold a worker in position or stop them reaching the fall edge, such as travel restraint and industrial rope access systems
  • Fall arrest: Systems that stop a fall after it has begun, such as safety nets, catch platforms, or full-body harnesses with shock-absorbing lanyards and anchor points. Fall arrest involves significant forces on the body and is a last resort

The WHS Regulations set the order (regulation 79): first, do the work on the ground or on a solid construction where reasonably practicable. If that is not possible, provide a fall prevention device. If that is not reasonably practicable, use a work positioning system. Fall arrest is the last option, and you may need a combination of controls.

Edge Protection

Edge protection is a passive fall prevention system installed at any open edge, penetration, or hole where a person could fall. Under the Code of Practice: Managing the risk of falls at workplaces, a guardrail system includes:

  • Top rail: Between 900 mm and 1100 mm above the working surface
  • Mid rail: Between the top rail and the toe board, preventing a person from sliding through
  • Toe board: At the base, preventing tools and materials from falling off the edge
  • Mesh or infill: Wire mesh infill panels can be used in place of mid-rails and toe-boards

Edge protection must be designed and constructed to withstand the force of someone falling against it (AS/NZS 4994 covers temporary edge protection). Holes, penetrations and openings must be made safe immediately after being formed, for example with covers or barricading. Edge protection must not be removed unless an alternative control is in place.

Scaffolding Safety

Scaffolding is one of the most common work-at-heights systems on construction sites. The rules governing scaffolding are strict:

  • A scaffold from which a person or object could fall more than 4 metres must be erected, altered and dismantled by a person holding a scaffolding high risk work licence (or a trainee under the direct supervision of a licensed scaffolder)
  • For suspended, cantilevered, spur and hung scaffolds, and any scaffold from which a person or thing could fall more than 4 metres, a competent person must inspect it and confirm in writing that it is complete before first use. It must then be inspected again after any incident that could affect its stability (such as a severe storm), after repairs, and at least every 30 days (regulation 225)
  • Guardrails, mid-rails, and toe boards must be installed on all open sides
  • Access to the scaffold must be via a proper stairway, ladder, or ramp β€” never by climbing the frames
  • Working platforms must be fully planked. Light duty platforms (up to 225 kg per bay) should be at least two planks wide (about 450 mm), and trestle scaffold platforms at least 450 mm wide. Medium duty (450 kg per bay) and heavy duty (675 kg per bay) platforms should be wider
  • Many sites use scaffold tags at each access point to show whether a scaffold has been inspected and is safe to use. Follow your site's tagging system, and never use a scaffold tagged as unsafe or incomplete
  • Never overload a scaffold beyond its rated capacity. Keep platforms clear of unnecessary materials

Harness Systems (Fall Arrest)

When fall prevention devices and work positioning systems are not reasonably practicable, a full-body harness and fall arrest system may be required. Workers who use these systems must be trained in their safe use, and using a harness correctly is a matter of life and death.

  • Full-body harness (AS/NZS 1891.1): Distributes fall arrest forces across the shoulders, chest, and thighs. Must have an attachment point suitable for fall arrest
  • Shock-absorbing lanyard: Limits the impact force on the body during a fall by tearing or extending in a controlled way to absorb energy
  • Anchor points: Each anchorage should meet the anchor strength specified in AS/NZS 1891.4 and be tested and approved by a competent person before use. Anchor points should be as high as the equipment permits, and work above the anchor point should be avoided
  • Fall clearance: Calculate the total fall distance before starting work: free fall distance + shock absorber deployment + harness stretch + the worker's height below the anchor. The Code of Practice says free fall should be no more than 2 metres (less is better), and there must be enough clearance below to prevent the worker hitting the ground or another surface
  • Rescue plan: If a PCBU provides a fall arrest system, it must establish emergency and rescue procedures, test them, and train workers in them (regulation 80). A person left hanging in a harness can suffer suspension intolerance, which can cause fainting and can be fatal, so rescue must happen as quickly as possible. Workers using a harness should never work alone
  • Inspection: Inspect all components before each use. Equipment that has arrested a fall must not be used again until a competent person has inspected it and certified it as safe

Ladder Safety

Ladders are often misused on construction sites. The Code of Practice says ladders should only be used for light duty work where tools can be operated safely with one hand, or as a means of access β€” not as a general working platform.

  • Set up single and extension ladders at a 4:1 slope (about 1 metre out for every 4 metres of working ladder height)
  • When a ladder is used for access, it should extend at least 1 metre above the stepping-off point on the working platform
  • Maintain three points of contact when climbing (two feet and one hand, or one foot and two hands)
  • Never carry tools or materials in your hands while climbing β€” use a tool belt or side pouch
  • Place the ladder on firm, stable ground with non-slip feet, and secure it at the top or bottom (or both). A second person may need to foot a stepladder
  • Do not stand on a rung closer than 900 mm to the top of a single or extension ladder
  • Never use metal or metal-reinforced ladders when working on live electrical installations
  • Inspect for bent rungs, cracked stiles, loose rivets, and damaged feet before every use

Roofwork

Roofwork is one of the highest-risk activities in construction. Falls from roof edges, falls through fragile roof materials, and falls through skylights are well-known causes of serious injuries and fatalities.

  • Fragile materials: Treat cement sheeting, fibreglass sheeting, skylights and rusty metal roofing as fragile. Never walk on them without proper crawl boards, safety mesh or other protection
  • Edge protection: Install perimeter guardrails or safety mesh before any worker accesses the roof
  • Skylight protection: Cover all skylights with load-rated covers or install guardrails around them
  • Weather conditions: Wet, icy, or windy conditions dramatically increase fall risk. Stop work when conditions are unsafe
  • Safe access: Use proper roof access systems such as scaffold stairways, roof hatches, or elevated work platforms. Do not use makeshift access methods

Regulatory Requirements Summary

  • Risk of a fall of more than 2 metres = high risk construction work = SWMS required
  • Scaffold from which a person or object could fall more than 4 metres = licensed scaffolder required
  • Those scaffolds must be inspected at least every 30 days, and after incidents or repairs
  • Fall arrest anchorages must meet the strength in AS/NZS 1891.4 and be approved by a competent person
  • Guardrail top rail height: 900 mm to 1100 mm
  • Ladder extension above stepping-off point: at least 1 metre
  • Emergency and rescue procedures are required whenever fall arrest systems are used

Key Takeaways

  • Falls from height are a leading cause of worker deaths in Australia, and the second most common cause nationally in 2025
  • Always prefer elimination, then passive fall prevention, before resorting to fall arrest
  • A SWMS is legally required for any construction work with a risk of a fall of more than 2 metres
  • Harness systems require proper training, fall clearance calculations, and a rescue plan
  • Ladders are for access and light work, not a general working platform β€” use a proper platform wherever possible
  • Never compromise on edge protection, and never remove it without an approved alternative

Practice Heights Safety Questions

Test your knowledge of fall prevention, scaffolding, and harness systems.

Start Practice Test

Sources and further reading (last reviewed November 2026)

WHS rules differ between states and change over time. Where this page states a legal or regulatory fact, it is based on the official sources below. If anything here disagrees with them, the official source wins. You can read how we check and correct our content.

This guide is free and kept up to date by one person. β˜• Support it